Metal Roof Fascia Dimension

Fascia Board Framing Construction Roof Construction Roof

Fascia Board Framing Construction Roof Construction Roof

Pin On Pergola

Pin On Pergola

Roof Eave Return Detail Roof Eaves Roof Detail Roof

Roof Eave Return Detail Roof Eaves Roof Detail Roof

Figure2 41 Jpg 710 688 Pixels Corrugated Metal Roof Metal Roof Installation Standing Seam Metal Roof

Figure2 41 Jpg 710 688 Pixels Corrugated Metal Roof Metal Roof Installation Standing Seam Metal Roof

Roofing Diagram Eaves Cross Section Framing Construction Home Construction Roof Construction

Roofing Diagram Eaves Cross Section Framing Construction Home Construction Roof Construction

4 Irresistible Hacks Building Roofing Design Roofing Light Ceilings Factory Roofing Architecture Roofing Standing Seam Metal Roof Metal Roof Shed Roof Design

4 Irresistible Hacks Building Roofing Design Roofing Light Ceilings Factory Roofing Architecture Roofing Standing Seam Metal Roof Metal Roof Shed Roof Design

4 Irresistible Hacks Building Roofing Design Roofing Light Ceilings Factory Roofing Architecture Roofing Standing Seam Metal Roof Metal Roof Shed Roof Design

Gable end truss drop 70mm avoiding kickouts up to 40 roof pitch.

Metal roof fascia dimension.

Wear soft soled shoes to improve traction and to minimize damage to the paint finish. Pure zinc roofing and guttering. 185mm external fascia and gutter is not suitable on concrete tile roofs with sloping soffits. The 147 small panel fascia system is suitable for use with metal tiles and roofs with sloping soffits up to 22 5 roof pitch.

Half round gutter 150mm and 200mm. Quad gutter 125 150 175 200mm. A high quality maintenance free solution for new and old buildings. Pre painted roofing and guttering.

The metal fascia should be supported on rafter clips at 1200mm maximum centres. Based on minimum purlin thickness of 45mm. For gable end roofs outriggers to be from finished timber size 90x45mm gable end truss drop 90mm. Many builders have the soffit sit on top of the window frame your horizontal mark will be dimension x minus 80mm to the suggested reference of the slot on the rafter bracket i e.

Novalinefascia must not be used as an end span support for sheet roofi ng. As an alternative to note 3 for gable end roofs outriggers to be from finished timber sizes 70mm x 45mm i e. Zincal roofing and guttering. Steel sheet roofing 1200mm tile roofing 600mm.

Flat back 135 and 180mm. Steel fascia this email address is being protected from spambots. Horizontal mark is 80mm above soffit line. Over 25 roof pitch a kickout may be required on all gable ends.

Manufacturer of roofing and rainwater products metal roofing flashings gutters fascia downpipes plumbing supplies in sydney nowra canberra victoria. A 10mm soffit clearance has been allowed for. Bullnosed and curve roofing. Fielders zincalume and colorbond steel fascia offers the new home builder an easy to install and maintenance free fascia with exceptional longevity as compared to timber.

It usually ranges from 305mm to 315mm for 22 5 degree roof pitches. Fascia installation procedure support spacings. The use of concrete tiles on the barge ends is not a recommended practice as highlighted in the nz metal roofing and cladding code of practice section 2 under. Always be aware of your position on the roof relative to any roof openings roof edges co workers and penetrations.

Fielders offer a comprehensive range of steel fascia to suit various gutter profiles and property styles. Og gutter 150mm 175mm 200mm. Metal roofing panels are slippery when wet dusty frosty or oily do not attempt to walk on a metal roof under these conditions. 150 multifit small panel fascia system is suitable for use with longrun metal tile roofs with sloping soffits up to 35.

Og gutter 125 mm.

Site Off Line Fine Homebuilding Breaktime Roof Construction Hip Roof Roof Detail

Site Off Line Fine Homebuilding Breaktime Roof Construction Hip Roof Roof Detail

The Taj Garage Bal Fz Roofing Detail Corrugated Steel Roofing Metal Roof Construction Corrugated Roofing

The Taj Garage Bal Fz Roofing Detail Corrugated Steel Roofing Metal Roof Construction Corrugated Roofing

Soffit And Fascia Installation Vinyl Siding Installation Installing Siding Diy Roofing

Soffit And Fascia Installation Vinyl Siding Installation Installing Siding Diy Roofing

Pin On Repairs

Pin On Repairs

Pin On Details

Pin On Details

Fascia Gutter Fascia Gutter Roof Detail Gutter

Fascia Gutter Fascia Gutter Roof Detail Gutter

Pin By Dave Duckers On Details Slate Roof Roof Framing Roof Construction

Pin By Dave Duckers On Details Slate Roof Roof Framing Roof Construction

Pin On Roofing

Pin On Roofing

Pin On Details

Pin On Details

Raising The Roof Roof Soffits Roof Architecture Roof Structure

Raising The Roof Roof Soffits Roof Architecture Roof Structure

Pin On Architecture Interiors

Pin On Architecture Interiors

How To Repair Gutters And Downspouts Doityourself Com Gutters Repair Diy Home Improvement

How To Repair Gutters And Downspouts Doityourself Com Gutters Repair Diy Home Improvement

Soffit Fascia Installation Vinyl Siding Installation Roof Installation Vinyl Siding

Soffit Fascia Installation Vinyl Siding Installation Roof Installation Vinyl Siding

Pin On Roof

Pin On Roof

Pin On Carport

Pin On Carport

Simple System Existing Slope Sheet Metal Coping Sketch Drawing The Image Shows A Sketch Of Metal Coping Installed Ov Roof Cladding Roof Architecture Roof Edge

Simple System Existing Slope Sheet Metal Coping Sketch Drawing The Image Shows A Sketch Of Metal Coping Installed Ov Roof Cladding Roof Architecture Roof Edge

Installing Soffit Fascia Home Construction Home Remodeling Building A House

Installing Soffit Fascia Home Construction Home Remodeling Building A House

Residential Timber Framed Construction Roof Construction Roof Framing Hip Roof

Residential Timber Framed Construction Roof Construction Roof Framing Hip Roof

3

3

Source : pinterest.com